Thursday, October 30, 2014

High Capacity Magazine Upgrades for Compact 22 Pistols

Shoot more, load less! If you own a Ruger SR22, Walther P22, or the new Smith & Wesson M&P Compact 22 pistol, then you know how much it sucks to be limited to only 10 rounds of 22LR per magazine. These magazine modifications will give you extra rounds in the clip so you can shoot more and load less. For the Walther P-22 magazines, you will get an extra 3 rounds in the factory 10 round mag. The Ruger SR-22 pistol mags will also be increased to 13 rounds over the stock 10. If you own the S&W M&P22 Compact, you will get 14 rounds in the factory 10 round magazine. That's 2 more rounds over it's full sized M&P 22 brother. Own one of those? Visit Taylor-Tactical-Supply.com and see our mag upgrades for that pistol to get 15 rounds over the factory 12.

Please note that with the shockbottle follower, you will loose the slide lock to open on the last shot fired (the slide will not lock back on an empty mag upon firing the last shot).

Due to US restrictions I can only ship to US addresses. Sorry for the inconvenience.

 Taylor Tactical Supply



shockbottle nictaylor00 Walther follower magazine upgrade high capacity P22 P-22
Walther P-22 P22 / P22Q / PPK / PPKS 22lr
13 Round Mag Modification



$12.99 +S/H



shockbottle nictaylor00 follower hi-cap SR-22

Ruger SR22, 13 Round Mag Modification


$12.99 +S/H




shockbottle nictaylor00 follower rounds modification upgrade hi-cap S&W

S&W M&P 22 Compact 14 Round              Mag Modification


$12.99 +S/H




traction grip friction performance tape decal S&W
Smith & Wesson M&P22 Grip Tape

Set of Three (3) $9.99

FREE SHIPPING























Sunday, October 5, 2014

AR15 Mil-Spec Trigger Adjustment Grip Screw

This ingenious screw design replaces the milspec factory grip screw to remove the trigger creep and travel from factory mil-spec triggers in the AR15 rifle. The kit comes with an adjustment screw, lock washer and wrench. The adjustment screw allows for tweaking the hammer and trigger engagement points to clean up the GI trigger and give you a cleaner trigger pull for increased accuracy.

http://www.taylor-tactical-supply.com/

AR-15 screw grip tweak adjust trigger job nictaylor00 M16 AR15 Colt DPMS Rock River Seekins Black Rain Bushmaster adjuster

Single


$14.95 ea


AR-15 screw grip tweak adjust trigger job nictaylor00 M16 screws adjuster

2 pack


$24.95




Add reduced power springs below to lighten the pull of your trigger for a super sweet do-it-yourself trigger job.





Install Directions:

1. The internal set screw comes with thread locker pre-applied but for best results remove the internal screw and apply additional thread locker and re install the set screw inside the
large screw. Make sure to screw down the internal screw all the way in so that the tip just protrudes.
2. Remove the factory grip screw and lock washer from the grip of your rifle. Mind the spring and detent for the safety as they may bounce out if you remove the grip completely.
3. With the hammer cocked and the gun on safe, insert the Trigger Adjustment Screw into the grip and tighten the large screw with a 3/16” hex wrench until he pistol grip is secure.
4. Using the included hex wrench, finger tighten the internal screw inside the 3/16” screw until the it stops. DO NOT OVER TIGHTEN. Backout the internal screw 1/4 turn at a time
until the safety lever can by actuated. Verify that the trigger, disconnector, hammer and safety function correctly. Let your additional thread locker dry before putting your rifle to use.