Thursday, October 22, 2015

How to Reduce Your AR15 Trigger Pull Weight Inexpensively

One of the easiest and least expensive ways to reduce the weight of the trigger on your AR15 rifle is to replace the stock hammer spring with a Reduced Power Spring. All you need is a punch or hex wrench small enough in diameter to push out the hammer pin located in your AR15 lower. Once you push out the hammer pin, the hammer and spring can be removed from the lower. Take note of the orientation of the spring as it sits on the hammer so that you can install the new spring in the same position.

Get it HERE
JP Enterprises, JPRifles, reduced, hammer, spring, power, trigger job, lighten, clean, gunsmith, DIY, simple, easy, inexpensive

Simply pull the spring off the hammer by grabbing one of the coils and pull. Install the Reduced Power Spring onto the hammer and reinsert the hammer/spring into the lower while pushing the hammer pin back into place through the lower. Be careful not to force the pin as you attempt to push it through the lower. Remember the lower is aluminum and the pin is steel, so forcibly hitting the pin or pushing harshly it may cause damage to your lower if all is not lined up perfectly.

JP Enterprises, JPRifles, reduced, hammer, spring, power, trigger job, lighten, clean, gunsmith, DIY, simple, easy, inexpensive

In our testing we were able to reduce the trigger pull weight by 3 pounds. Our stock trigger was measuring 7 pounds with the mil-spec hammer spring found in all Lower Parts Kits (LPK). Once we installed the Reduced Power Spring, our same trigger measured 4 pounds of pull. This is a considerable amount of reduction for such a low price. Most match triggers run well over $100. Granted, this spring does nothing to reduce the creep or "grittiness" of your stock trigger like the drop-in match triggers do, but you can come close with the additional Adjustment Grip Screw Kit. For those not wanting to spend alot of money on an expensive trigger for their rifle or carbine, the Adjustment Screw and Reduced Power Hammer Spring Kit is the way to go.





Application: The Reduced Power Hammer Spring is intended for competition and recreational use only and should not be installed in any rifle used for defense or duty applications. By reducing the spring tension, the introduction of light strikes or failures to fire due to the lack of primer detonation may occur.

Friday, September 18, 2015

Taylor Tactical Website Launched!

website, sales, nictaylor00, shockbottle, 1911, springs, basepads, taylortacticalsupply

www.TaylorTacticalSupply.com


After selling on Ebay and Amazon for the past few years and dealing with the limitations of political correctness when it comes to firearms, we decided to launch our own website. This allows us to showcase our products and others in a more friendly environment. We continue to sell on Ebay and Amazon but having our own site helps with what we can't post on those other places. We will continue to offer products here on the Blog but the website will have a much larger variety and should be much more easier to navigate.

For all your 22 pistol needs remember the website www.22LRupgrades.com If you are looking just for GSG & Sig Sauer 1911 parts, all you need to remember is www.GSGparts.com We continue to offer calibration spring kits for the full sized 1911 to those looking to enhance the performance of there pistol at www.1911springs.com Finally we offer a variety of aggressive Grip Tape patterns for various pistols www.Pistol-GripTape.com (sold in sets of 3 unlike other merchants).

We are constantly looking to add product to our store. If you have a product and offer dealer pricing, contact us at sales@TaylorTacticalSupply.com

Taylor Tactical LLC
13492 Research Blvd
Suite 120, #158
AUSTIN, TX 78750

Due to the nature of this business, and international regulations (ITAR) we are limited in what we can sell to anyone that is not in the United States. At this point only our GripTape decals for various firearms can ship outside the US.  All other international orders will be canceled.


Tuesday, August 4, 2015

POV Action Cameras, Which one to Choose?

Today action camera choices seem limitless and overwhelming. For me and self filming my shooting activities, I find that form factor plays a major roll when it comes to choosing one. That means the GoPro is not my 1st choice for an action camera to capture those First Person Shooting Videos or FPS. I prefer the Contour brand cameras because of the form factor and mounting options. They allow a more realistic view that better conveys the shooting experience as if the viewer was actually pulling the trigger. I'm now experimenting with the Sony Action Cameras and I find them to be a big plus for three important features. One, the Sony has a similar form factor of the Contour line of cameras. Two, the Sony has image stabilization in it's action cameras. This is HUGE! At the time of this review, no other action camera maker has this feature that I am aware of. Three, the Sony has OUTSTANDING audio. ALL action cameras suffer when it comes to their microphone and interface circuitry. Over the years I've noticed that the Sony camcorders seem to have a better microphone system compared to others I've used. This is also true for their action cameras.

If you are a GoPro junkie and will use nothing other than the square box... then you need to look at the W8 Action Camera. It is a Chinese knockoff of the GoPro but at literally a fraction of the cost. And the cool thing, it uses the GoPro mounting systems. I found my W8 to have very good video quality but bad audio (just like GoPro and others). The W8 also can be controlled with your smart phone via WiFi and a free downloaded App.

Wednesday, July 22, 2015

Desert Eagle 50AE, Not Just a Video Game Weapon

For those that have seen or use the Desert Eagle pistol in your video game play or even airsoft wars. Most of you know it shoots a 50 caliber bullet but have most likely never held or even seen the gun and its ammo. The first video below is shot with a high speed camera with a relatively new shooter attempting to shoot a bowling pin with the 325 grain projectile. Note the recoil or flip of the gun and the huge fireball. Keep in mind this video was shot in daylight. The flash from the muzzle is blinding in the dark.



Want to see more details and a closer look at the Desert Eagle 50 AE? This video below is a review of the gun. Be sure and watch to the end for some footage of other new shooters taking shots with it and a Freedom Arms revolver chambered in the same 50AE cartridge. That revolver is not for a new shooter. The recoil is unbearable.



In the videos below I will show you the process of reloading this monster 50AE (50 Action Express) round. Even though the video(s) is caliber specific, the information on the process is pretty much universal for reloading other calibers. If you are curious about reloading or looking for information on the subject, these two videos are for you.







Tuesday, July 14, 2015

RCBS Chargemaster 1500 Defect & DIY Repair

After many years of dealing with my RCBS Chargemaster 1500 combo that appears to have an issue with responsiveness in reference to the keypads, I decided to make the following video and send it to RCBS and see if they had a solution for the issue.  Be sure to see what really fixed the scale near the end of this post.



Here is RCBS's response via email:

SOMETIMES THIS IS DUE TO THE CONNECTION ON BOTH UNITS. DISASSSEMBLY BOTH UNIT AND APPLY ELECTRICAL GEL ON BOTH CONNECTION PORT. REASSEMBLY AND PRESS FIRM ON BOTH UNITS WHEN ATTACHING THIS WILL GIVE A GOOD CONNECTION WHEN COMMUNICATING. USE A LAUNDRY STATIC REMOVER SHEET TO REMOVE ANY STATIC ON THE BLACK PLATEN. RECALIBRATE YOUR SCALE AND LET US KNOW.

So I gave the reccomendation a try. Here are the results:


In short the procedure RCBS recommended did not fix the issue. Below is the email exchange with the RCBS tech. I realize that my particular unit is clearly out of warranty and I do not have any illusions that RCBS would repair of fix my unit for free. However I thought it odd that RCBS would not "middle" any repair work since they have the most knowledge of the product and connections to the manufacturer. But instead they pointed me in the direction of a "calibration" equipment company when calibration is clearly not the issue.

If anyone knows how to fix the problem seen in the video, please let me know.

Nic:
I finally got to try out the suggestion and the problem still exists. Can you assign an RMA number so I can send this scale and powder dispenser in for repair? I have the original box to ship it in.

RCBS:
HOW LONG HAVE YOU HAD THIS UNIT?

Nic:
it's been years. 5 maybe???

RCBS:
I AM SORRY WE DO NOT REPAIR THESE CHARGEMASTER UNIT. WE PURCHASE THESE CHARGEMASTER 1500 COMBO SCALE AND OUR VENDOR DOES NOT ALLOW US TO REPAIR. PLEASE TRY TO CONTACT MICRO PRECISION CALIBRATION INC 1-530-268-1860 AND SEE IF THEY CAN REPAIR THE UNIT.

Nic:
Hold on. You sell your branded RCBS unit, but do not repair or replace? But rather direct issues back to the OEM/ODM?

What is the website and address of the OEM/ODM?

RCBS:
THESE UNITS ARE PURCHASE OVER SEAS BY EXCELL.

Nic:
I did contact RCBS right? Not some other vendor? I find it odd that the company that brands and sells its product with it's company name on the product would point to the vender for issues and not the company that sells and markets their own products.

Seems kinda like buying a Ford and having an issue with the Ford and then Ford referring the customer to the plant that assembled the Ford.

Here's the site associated with that phone number

http://www.microprecision.com/calibration-contact/

I do not think calibration is the issue. I will dispose of the unit and go with another brand. Thanks for your time.

RCBS:
I AM SORRY TO LOSE ANOTHER CUSTOMER BUT THIS IS JUST WHAT THE POLICY ON THESE CHARGEMASTER UNITS. THERE IS 1 YR WARRANTY FROM FACTORY FROM THE DATE OF PURCHASE. MICRO PRECISION CALIBRATION IS JUST ONE OF ANOTHER COMPANY THAT I KNOW THAT MIGHT HELP. THIS MICRO PRECISION CALIBRATION DOES NOT ASSOCAITE WITH US RCBS.

Nic:
Yeah, I paid the extra for RCBS when shopping for a scale because there are plenty of other brands cheaper for the same features. However, I've had good luck with RCBS until now. But it looks like the extra expense was not worth the frustration in this case. For what it is worth, I've had this issue for years with this scale. I finally got tired of messing with it.

THE FIX
After taking a few says to think on it, I borrowed another Chargemaster 1500 from a friend and swapped the parts of the unit and was able to isolate the defective part. Turns out my powder dispenser unit was causing the problem. I voided the warranty (already out of date) and took it apart with 4 simple screws. Take care not to damage the ribbon cable inside when you unplug it from the small PCB inside the dispenser.


After inspecting the little PCB I found that the connector that connects the dispenser to the scale had "cold solder joints". Cold solder joints are solder joints that did not cool or flow properly when the soldering process took place at the factory. This is a manufacturing defect and should have been caught by the QA process at the time of manufacture.



This is a relatively simple fix assuming you have a soldering iron. Just reflow the solder joints on the BERG connector so that the frosty looking solder joint is nice and shinny. Adding solder to the joint and using flux will make it easier to reflow. The video below shows a sample of the soldering process and speaks more in depth of the error.



Sunday, March 8, 2015

AR15 Compensators - Do They Really Reduce Recoil ?



This is an experiment I've been wanting to do for a long time. So having a Monday off for MLK Day, I headed to the ranch with no kids to distract me.

I was curious about the effects of a compensator or muzzle brake if you could eliminate the human factor. So I strapped my rifle to a work bench stand and used the Hands Off Trigger Release to actuate the trigger. Capturing the results of each muzzle brake with the video camera, I was able to see the linear effectiveness of each brake.

My conclusion is fairly obvious... any compensator is better than nothing at all. However, every muzzle brake I tested but one (the Dragon's Head from Surplus Ammo) performed the same as far as the X & Y movement of the rifle is concerned. This result was most unexpected. I was expecting to see much more of a difference between the muzzle brakes. I suspect with all the various models on the market and all linear movement being equal, there has to be a difference in how they perform on the Z axis. I have a few ideas how to test for this so I may give that a try.









m16 ar15 rifle carbine muzzle flash hider comp compensator brake military A1 A2
A1 Flash Hider
m16 ar15 rifle carbine muzzlelinear comp compensator brake military surplus ammo
Surplus Ammo & Arms (SAA) "Dragon's Head"
m16 ar15 rifle carbine muzzle flash enhancer comp compensator brake military
Double Star "Flash Enhancer"
m16 ar15 rifle carbine muzzleJP Enterprises tactical comp compensator brake military
JP Enterprises
m16 ar15 rifle carbine muzzle Lantac Dragon 556 comp compensator brake military
Lantac "Dragon Advanced Muzzle Brake"
m16 ar15 rifle carbine muzzle Surefire flash hider comp compensator brake military
SureFire
m16 ar15 rifle carbine muzzle flash hider comp compensator brake military AAC Advanced Armament blackout
Advanced Armament Corporation (AAC) "Blackout 51T"
m16 ar15 rifle carbine muzzle Bnaks Bullets comp compensator brake military
Banks Bullets
m16 ar15 rifle carbine muzzle flash hider comp compensator brake military AAC Advanced Amrament 51t breakout
Advanced Armament Corporation (AAC) "Breakout 51T"






Wednesday, January 21, 2015

Walther P22, PPQ, P22Q, PPK, PPKS 22LR & G22 Bullpup High Capacity Magazine Upgrades


Walther PPQ 22LR pistol tactical M2 rimfire nictaylor00 shockbottle follower high cap capacity modifiaction

Shoot more, load less! If you own a Walther PPQ then you know how much it sucks to be limited to only 12 rounds of 22LR per magazine. These magazine modifications will give you extra rounds in the clip so you can shoot more and load less. You will get an extra 3 rounds in the factory 12 round mag. That's 15 rounds in the magazine and one in the chamber.

We also have magazine upgrades for the Walther G22, P22, P22Q, PPK and PPKS.  Our modifications will get you 13 rounds in the magazine over the factory 10. Visit our website for current inventory and more parts at www.22LRupgrades.com

Please note that with the shockbottle follower, you will loose the slide lock to open on the last shot fired (the slide will not lock back on an empty mag upon firing the last shot).

Due to US restrictions I can only ship to US addresses. Sorry for the inconvenience.

http://www.taylor-tactical-supply.com/




Walther PPQ 22LR pistol tactical M2 rimfire nictaylor00 shockbottle follower high cap capacity modifiaction
Walther PPQ, 15 Round Mag Modification



$12.99 +S/H




Walther PPQ 22LR pistol tactical M2 rimfire nictaylor00 shockbottle follower high cap capacity modifiaction

Walther PPQ, 12 Round Magazine


SOLD OUT







shockbottle nictaylor00 Walther follower magazine upgrade high capacity P22 P-22
Walther P-22 P22 / P22Q / PPK / PPKS 22lr
13 Round Mag Modification



$12.99 +S/H

shockbottle nictaylor00 Walther follower magazine upgrade high capacity P22 P-22
Walther P22, 10 Round Magazine


$29.99 +S/H





Walther G22 Bullpup rifle carbine 22LR pistol tactical M2 rimfire nictaylor00 shockbottle follower high cap capacity modifiaction

Walther G22, 13 Round Mag Modification


$12.99 +S/H