Remington 1100 3-Gun Competition Parts

Thinking of getting a shotgun for 3-gun competition? If you already have a Remington 1100 or 1187, see the list of parts below to modify that old shotgun.

Combat Bolt Handle Increased size allows you to reach over the receiver and operate the bolt with your ''''off'''' hand without taking your finger out of shooting position. Provides plenty of extra leverage to help clear a jammed chamber in only seconds. Reverse contour and open center design gives better grip with gloved hands. Easy to install requires no alteration to gun. Mfg: Choate SPECS: 4140 Steel blued finish. Handle is 1.25'''' (3.1cm) high 7/8'''' (22mm) wide. Fits Remington 1100 11-87 only.

Shotgun Magazine Extension - 12 Ga Blue Mag Ext 4-Rds Fit Rem. 870/1100/11-87* Gives you additional magazine capacity in only a minute. Quick and simple to install and remove. Threaded tube replaces magazine cap screw. Perfect for Shotgun Action Shooting events or Law Enforcement. Sling Swivel Clamp (included on Remington models only) secures extension to the barrel for extra support. Provides a convenient front mounting point for carry strap or sling. Sling Swivel Clamp also available separately. Mfg: Choate SPECS: Extension - Steel blued or parkerized matte finish. 12 ga. only. Includes extended spring follower and swivel clamp. Sling Swivel Clamp - Blued or parkerized steel front and rear 1" swivel rings with studs. Chart indicates number of ROUNDS (RDS) in addition to factory magazine capaci

Remington 870 / 1100 / 11-87 Big Speed Safety - Big Speed Safety Large dome-shaped button is quick to locate. Just a quick push with the side of your trigger finger will disengage the safety. Round profile does not snag clothing or guncase liner. Drop-in installation right-hand use only. Mfg: Vang Comp Systems SPECS: Steel blue polished finish. .960'''' (24.4mm) long. Head - .350'''' tall (8.9mm .433'''' (11mm) diameter.

Remington 1100/11-87 Easyloader - Easyloader Creates a giant ramp that aligns the shell with the magazine tube for faster and easier reloading with either hand. Completely replaces the small factory carrier release button. Made from durable stainless steel; very easy to install only minor fitting required. Mfg: Daves Metal Works SPECS: 17-4 stainless steel. 2-'''' (6.3cm) long '''' (19mm) wide. Includes roll pins and installation instructions. Fits Rem. 1100 11-87 Sportsman 12 in 12 ga. only.

Side Saddle Shell Holder - Fits Remington 870/1100/1187 6 Rnds 12 Ga Lightweight molded-nylon shell carrier puts additional fire power quickly within your reach. Aluminum mounting plate attaches to the side of the receiver using the existing pin/screw holes-no permanent alterations or gunsmithing required. Four- and six-round models available for a variety of popular law enforcement shotguns. Rem. 870/1100/11-87 ESN has a convenient window in the mounting plate that leaves the weapon's serial number exposed for viewing with the shell holder installed. Designed for armorers and law enforcement agencies who track their firearms by serial number for inventory maintenance and record keeping. Mfg: Tacstar SPECS: Shell Holder - nylon plastic black. Mounting Plate - aluminum black matte finish. 63⁄4" (17cm) long 5.3 oz. (152 g) wt. (6-round). Includes mounting screws pins and instructions. Field-grade forends that extend onto the sides of the receiver must be modified or replaced to pro

Remington 1100/11-87 Gas Ring & Barrel Seal Kit - Gas Ring & Barrel Seal Kit Remington factory components Replacement gas system parts for your Remington 1100 and 11-87 shotguns Includes steel piston piston seal and barrel seal Includes factory installation instructions Fits 12 & 16 gauge also older large frame 20 gauge models with "X" or "N" as a suffix to the serial number Mfg: Remington